Menu

Znergy Cable

Australian Cable Manufacturer

header photo

A Guide To Buy Low, Medium & High Voltage Cable

Low Voltage: up to 1000V

Medium Voltage: between 1000 V and 35 kV

High Voltage: between 35 kV and 230 kV

Extra High Voltage: from 230 kV and above


Medium and high voltage are particularly important for heavy-duty applications that demand motors with outputs of 400 kW and higher. Because of the increased voltage, smaller cables can be used, lowering distribution cable costs significantly.

"It is feasible to reduce the current by increasing the voltage. This allows for the use of smaller distribution cables. If wires must be put over long distances, such as in tunnels, a greater voltage is an obvious choice."

MV Cable (Medium-Voltage Cable)

Medium-voltage cables are frequently used in mobile substation equipment, for power distribution in industrial settings, and in mining to power drills, shovels, haulers, and other equipment. Standard voltages for these cables include 5,000, 8,000, 15,000, 25,000, and 35,000 V.

Utilities staff utilise mobile workstations to provide scheduled downtime maintenance for substations or to undertake repairs due to damage caused by a storm, which is a popular application for medium-voltage lines.

Furthermore, because certain industrial facilities are responsible for some of the electricity that comes into them, they may have an in-house staff or contractors who build and repair these types of cables for power distribution.

The building of low- and medium-voltage cables is perhaps the most significant distinction. Most medium-voltage designs have extra protection to prevent possible charges from accumulating anywhere along the line.

A typical single-conductor, low-voltage design consists of the following components:

  • Insulation,
  • jacketing, and
  • an aluminium or copper conductor


The following is an example of a medium-voltage design:

 

  • a conductor constructed of aluminium or copper, • a conductor shield made of some form of semiconductor material,
  • The use of insulation,
  • Insulation shield, which can be a semiconductor, a metallic braid or tape, or a combination of the two; and
  •  Jacketing


The conductor and insulation shields help to decrease the impact of cable defects or coming into touch with a ground potential, where voltage can collect. Because electricity always seeks the lowest point of resistance, the semiconductor, copper tape, or metal braid is used to spread the charge out more evenly. "No application or cable is flawless, "therefore there will be areas on that cable where there might be a slightly thinner jacket or contact with ground, resulting in a lower point of resistance." "A charge will try to accumulate there because it is looking for ground potential." These charges can build up and discharge without the conductor shield or the insulation shield."

This safety feature guards against potential discharges that could harm the cable, equipment, or, worse, cause injury.

Basics of HV Cable (High Voltage Cable)

In a variety of internal combustion engines, high tension cables are used to connect the ignition coil, distributor, or magneto to each spark plug. They're employed in a variety of places, including AC and DC power transmission, ignition systems, and instrumentation. You must ensure that the cable's insulation does not deteriorate due to high-voltage stress and ozone produced by tracking or electric discharges on air while using these cables. The cable system should also check for high-voltage conductor contact with other objects and leakage current. Cable couplings and terminals are typically intended to control high-voltage stress and prevent insulation failure. These cables frequently feature a metallic shield over the insulation that is connected to the ground and designed to equalise the dielectric stress of the insulation layer.

LV Cable (Low Voltage Cable)


The fundamental function of low tension cables is to eliminate power shortages between posts. Because of the cable's low tension, large prints on both ends are squeezed. Individual tensions known as "runs" have a height of 200']0ft. with an anchor assembly at each end, and these cables lack tension. Low tension cables are typically placed on the ground as a precaution against multiple post damages due to this unique feature.

 

What is the Best Way to Choose Wires and Cables?


When shopping for wires and cables, there are a few things to consider as a buyer. Here are some of the most significant considerations to make while choosing different types of wires and cables: -

  • Voltage

  • strength and durability

  • ability to handle heat

  • size of the cable

Why Australian Cable for Wires & Cables?


The electrical wires we offer come in a variety of sizes and types.

When searching for electrical wires, keep in mind that they are always insulated, which is not necessarily the case with other types of cables. Copper is sometimes used in electrical wires because of the multiple benefits it provides. Steel is used to make other sorts of wires. Insulation on the electric wire is required to prevent shocks and short-circuits from occurring between them.

It's always a good idea to know exactly what type of application you're looking for. Because there are so many different types of wires and cables on the market, you'll need to be very specific when looking for them on znergy cables.

Go Back

Comment

Blog Search

Blog Archive

Comments

There are currently no blog comments.